Manual Mando Universal Sony Rm - V202
Control Remoto Universal Sony Rm-v301
Sony RM-V502, RM-V402, RM-V302, RM-V202 & RM-EZ2 Quick Programming Instructions: Enter preset codes: Press S and Power at the same time. Select the Component button you would like to configure. Enter the three-digit code from the code list, followed by ENT to save. Test the entered code – if it does not work, repeat this procedure. Search for preset codes: Press S and Power at the same time.
Instructions for setting up the. Sony RM-V202. 4 Component Universal Remote Control. 1) Find the Component Code number for the desired Device from the table below.
Select the Component button you would like to configure. Now, alternate between pressing the Channel + and Power buttons. When the Power button turns your device on or off, press ENT to save the code. Changing the type of component on a button: Does not apply to the RM-V502 or RM-EZ2. Press S and Power at the same time. Select the Component button you would like to configure (all may be changed except for TV and VCR). While pressing the Stop button, press the digit from the table below that corresponds to the new type of component you would like to control, followed by ENT to save the change.
RM-V402 & RM-V302 1 VCR 3 DSS Receiver, Digital Cable Box, Digital Video Recorder 4 Receiver 5 CD Player 6 Tape Deck 7 MD Deck, DAT Deck 8 Television 9 Analog Cable Box 0 DVD Player RM-V202 1 VCR 3 DSS Receiver, Digital Cable Box, Digital Video Recorder 8 Television 9 Analog Cable Box 0 DVD Player For the RM-V502: after entering setup by pressing S and Power at the same time, repeatedly press the component button you would like to change until the desired component type is shown on the LCD screen. Reassign the volume buttons: Does not apply to the RM-V202 or RM-EZ2.
Kalashnikov spetsnaz airsoft gun. Cybergun Kalashnikov AK47 BETA Spetsnaz Manual. CYBERGUN Airsoft Manuals.
Press S and Power at the same time. Press the Receiver component button.
If you would like to use the receiver’s volume controls for all components, press the Volume + button. If you would instead like to use the TV’s volume control under video devices and the receiver for audio devices, press Volume -. Program Component Select macros: Does not apply to the RM-V402, RM-V302, RM-V202 or RM-EZ2. Press S and the component button you would like to assign the macro to. Now, navigate the remote and enter up to 16 commands in the order you would like them replayed.
Note that device changes count as a step. To save the macro press S. To play the macro back you will need to hold the component button for 2 seconds. Clear a Component Select macro: Does not apply to the RM-V402, RM-V302, RM-V202 or RM-EZ2.
Hold the component button with the macro you would like to clear and enter 0 and ENT in sequence. Program channel macros: Does not apply to the RM-V502, RM-V202 or RM-EZ2. Select the component button you would like to program the macro for. Only buttons set to operate televisions, analog cable boxes, digital cable boxes, DSS receivers or digital video recorders can be used.
Now, press and hold the macro key you would like to program. This can be either Play, Rewind, Fast Forward, Stop, Pause or Record. While holding that button, enter the channel number you would like to have the remote transmit on the numerical keypad. Up to four digits can be saved, including a final Enter command. To save the macro, release the button you are holding. Clear a channel macro: Does not apply to the RM-V502, RM-V202 or RM-EZ2.
Universal Sony Rm Ez4 Remote Codes
Select the component button that contains the macro you would like to reset. Hold down the macro button you wish to clear, enter 0 and ENT in sequence, then release the macro button. Reset the remote to factory defaults: Press the Power, TV/Video and Volume - buttons simultaneously.